XDB101-3 Flush Diaphragm Ceramic Pressure Sensor Isithombe Esifakiwe

I-XDB101-3 Flush Diaphragm Ceramic Pressure Sensor

Incazelo emfushane:

I-XDB101-3 yochungechunge lwe-flush diaphragm Ceramic pressure sensor iwumgogodla wakamuva we-micro-pressure pressure ku-XIDIBEI, enamabanga okucindezela ukusuka ku- -10KPa kuye ku-0 kuye ku-10Kpa, 0-40Kpa, kanye no-0-50Kpa.Yenziwe ngo-96% Al₂O₃, okuvumela ukuthintana okuqondile nemidiya eminingi ene-acidic ne-alkaline (ngaphandle kwe-hydrofluoric acid) ngaphandle kwesidingo semishini eyengeziwe yokuvikela ukuzihlukanisa, ukonga izindleko zokupakisha.

Thumela i-imeyili kithi

Imininingwane Yomkhiqizo

Omaka bomkhiqizo

Izici

● Ibanga Lokulinganisa: -10KPa…0KPa～40KPa…50KPa.

● Usayizi: 32*(4+X)mm.

● Ukuthembeka okuphezulu, nezinketho zokukhipha ezivumelana nezimo.

Izicelo Ezijwayelekile

● Ukulawulwa kwenqubo yezimboni

● Izimo ze-Micro-pressure

● Izinga loketshezi noma isilinganiso somfutho wothuli

● I-XDB101-3 flush diaphragm Ceramic pressure sensor ingasetshenziswa ekulawuleni inqubo yezimboni kanye nesilinganiso somfutho wezinga loketshezi.

isilinganiso sokucindezela kwezimboni koketshezi lwegesi nesitimu

Isithombe esibheke phezulu esinqeni sesisebenzi sezokwelapha esigqoke imaski eyisivikelo ethinta imonitha yemishini yokufaka umoya.Indoda ilele embhedeni wasesibhedlela ngemuva esilufifi

Imingcele Yezobuchwepheshe

Ibanga lokucindezela	-10KPa…0KPa～40KPa…50KPa	Usayizi mm(ubude be-diaphragm*)	32*(4+X)
Imodeli yomkhiqizo	I-XDB101-3	I-voltage yokuhlinzeka	0-30 VDC (ubukhulu)
I-impedance yomgwaqo webhuloho	10 KQ±30%	Okuphumayo kwebanga eligcwele	≥2 mV/V
Izinga lokushisa lokusebenza	-40~+135℃	Izinga lokushisa lesitoreji	-50~+150 ℃
Izinga lokushisa lesinxephezelo	-20 ~ 80℃	Ukwehla kwezinga lokushisa(uziro nokuzwela)	≤±0.03% FS/℃
Ukuzinza kwesikhathi eside	≤±0.2% FS/ngonyaka	Ukuphindaphinda	≤±0.2% FS
I-Zero offset	≤±0.2 mV/V	Ukumelana ne-insulation	≥2 KV
Ukuzinza kwesikhathi eside kwephoyinti elinguziro @20°C	±0.25% FS	Umswakama ohlobene	0~99%
Ukuthintana okuqondile nezinto eziwuketshezi	96% Al₂O₃	Ukunemba sekukonke(linear + hysteresis)	≤±0.3% FS
Ingcindezi yokuqhuma	≥2 ububanzi bezikhathi (ngobubanzi)	Ingcindezi yokulayisha ngokweqile	150% FS
Isisindo senzwa	12g

XDB101-3 umdwebo wezintambo zenzwa yokucindezela

Amanothi

1. Uma ufaka i-ceramic sensor core, kubalulekile ukugxila ekufakweni kokumiswa.Isakhiwo kufanele sifake indandatho yengcindezi engaguquki ukuze kukhawulwe indawo ye-sensor core futhi kuqinisekiswe ngisho nokusatshalaliswa kokucindezeleka.Lokhu kusiza ukugwema ukwehluka ekukhuleni kwengcindezi okungavela kubasebenzi abahlukene.

2. Ngaphambi kwe-welding, yenza ukuhlolwa okubonakalayo kwe-sensor pad.Uma i-oxidation ikhona endaweni yephedi (iyenze ibe mnyama), hlanza iphedi ngerabha ngaphambi kokulishisela.Ukwehluleka ukwenza kanjalo kungase kubangele ukuphuma kwesignali okungekuhle.

3. Uma ushisela izintambo zokuhola, sebenzisa itafula lokushisa elinokulawula ukushisa okubekwe ku-140-150 degrees.I-soldering iron kufanele ilawulwe cishe ngama-degree angama-400.I-flux esekelwe emanzini, engahlanjululwanga ingasetshenziselwa inaliti yokushisela, kuyilapho ukunamathisela okuhlanzekile kwe-flux kunconywa ngocingo lokushisela.Amalunga e-solder kufanele abe bushelelezi futhi angabi nama-burrs.Nciphisa isikhathi sokuthintana phakathi kwe-ayina e-soldering kanye nephedi, futhi ugweme ukushiya i-ayina e-soldering kuphedi yenzwa ngaphezu kwamasekhondi angu-30.

4. Ngemuva kokushisela, uma kunesidingo, hlanza i-flux esele phakathi kwamaphoyinti wokushisela usebenzisa ibhulashi elincane elinengxube yezingxenye ezingu-0.3 ze-ethanol ephelele kanye nezingxenye ezingu-0.7 zokuhlanza ibhodi lesifunda.Lesi sinyathelo sisiza ukuvimbela ukugeleza kwensalela ekukhiqizeni amandla e-parasitic ngenxa yomswakama, okungase kuthinte ukunemba kwesignali yokuphumayo.

5. Yenza ukutholwa kwesignali yokuphumayo kunzwa eshiselwe, uqinisekise isignali ephumayo ezinzile.Uma ukweqa idatha kwenzeka, inzwa kufanele ishiswe kabusha futhi ihlanganiswe kabusha ngemva kokudlulisa ukutholwa.

6. Ngaphambi kokulinganisa i-sensor post-assembly, kubalulekile ukubeka izingxenye ezihlanganisiwe ekucindezelekeni ukuze ulinganise ukucindezeleka komhlangano ngaphambi kokulinganisa isignali.Ngokuvamile, ukugibela ibhayisekili eliphezulu nezinga lokushisa eliphansi kungasetshenziswa ukuze kusheshiswe ukulingana kwengcindezi yengxenye ngemva kwenqubo yokunwetshwa nokufinyezwa.Lokhu kungafezwa ngokubeka izingxenye ezingeni lokushisa -20℃ kuya ku-80-100℃ noma izinga lokushisa lekamelo libe ngu-80-100℃.Isikhathi sokufaka emazingeni okushisa aphezulu naphansi kufanele sibe okungenani amahora ama-4 ukuze kuqinisekiswe imiphumela emihle.Uma isikhathi sokufakelwa sisifushane kakhulu, ukusebenza kahle kwenqubo kuzoba sengozini.Izinga lokushisa lenqubo ethile kanye nesikhathi sokufakelwa kunganqunywa ngokuhlola.

7. Gwema ukunwaya i-diaphragm ukuze uvimbele ukulimala okungaba khona kumjikelezo wangaphakathi we-ceramic sensor core, okungase kuphumele ekusebenzeni okungazinzile.

8. Qaphela ngesikhathi sokukhweza ukuze uvimbele noma yimiphi imithelela engase ibangele ukungasebenzi kahle kwe-sensing core.

Sicela uqaphele ukuthi iziphakamiso ezingenhla zokuhlanganisa izinzwa ze-ceramic ziqondene ngqo nezinqubo zenkampani yethu futhi zingase zingasebenzeli njengamazinga ezinqubo zokukhiqiza amakhasimende.